ES | CN

ETA approved NJMKT anchors and epoxy resin

Home >> News

Selecting an ETA Chemical Anchor Maker for C1/C2 Seismic Use

Nov. 19, 2026


Engineers specifying post-installed rebar connections in seismic zones face a recurring question before construction begins: which chemical anchoring adhesive can be trusted to hold under cyclic loading, moisture exposure and decades of service without relying on an imported product line that may lack local technical backup. That question becomes sharper on projects such as nuclear facilities, rail infrastructure and tunnels, where anchor failure is not an acceptable risk and documentation has to satisfy both structural engineers and regulators.

For buyers comparing suppliers, the starting point is independent certification rather than marketing language. European Technical Assessment (ETA) approval is one of the few third-party frameworks that tests chemical anchors under cracked-concrete conditions and assigns seismic performance categories such as C1 and C2, with C2 covering the more demanding high-seismicity scenario. A manufacturer holding ETA certification for its anchoring adhesive has had the product's bond strength, creep behavior and fatigue response verified against a defined protocol, which gives specifiers a basis for comparison that does not depend solely on a supplier's own test reports.

Nanjing Mankate Science & Technology Co., Ltd., a Nanjing-based manufacturer of reinforcement and anchoring materials founded in 2004, positions its MT-500 Injectable Rebar Adhesive around this certification gap. The epoxy-based product is intended for chemical anchoring of rebar and threaded rods in concrete and granite, and the company states that its service life has been verified at 100 years under ETA assessment. The adhesive carries a C2 seismic rating, meaning it is designed to maintain anchoring performance under high vibration and seismic loading rather than static conditions alone.

Beyond the seismic classification, several material properties bear directly on a selection decision. MT-500 is rated for an operating temperature range of -40°C to +160°C and is formulated for use on dry, humid and underwater substrates, with water absorption specified at as low as 0.02%, a factor relevant to installations in tunnels or marine-adjacent structures where moisture ingress is a known failure mode for lower-grade adhesives. The product reaches a load-bearing cure state within 1.5 to 2 hours at room temperature, and the company reports RoHS compliance and VOC-free formulation, which matters for enclosed worksites such as underground rail tunnels. Mankate states its products are manufactured to comply with China's GB 50367-2013 and GB 50728-2011 structural standards, alongside ISO 9001, ISO 14001 and ISO 45001 management certifications and CE marking.

One reference point the company cites for nuclear-grade requirements is the Tianwan Nuclear Power Plant, where MT-500 was supplied for rebar anchoring under what the company describes as nuclear-grade safety requirements. For specifiers, this indicates the type of risk tolerance the product has been positioned for, though acceptance criteria differ by project and should be verified independently for each application.

For a buyer narrowing down a chemical anchor supplier, the practical checklist implied by this profile includes confirming current ETA certification status and seismic category, checking the substrate and moisture conditions against the adhesive's tested range, and reviewing cure time against the project schedule. Mankate also states that its anchoring products are insured through Ping An Insurance and are backed by a 24-hour technical support line along with free technical documentation and 3D construction videos, elements that affect post-purchase support rather than the adhesive chemistry itself but are relevant to a procurement decision on infrastructure work.

About Nanjing Mankate Science & Technology Co., Ltd.

Founded in 2004 and headquartered in Nanjing, China, Nanjing Mankate Science & Technology Co., Ltd. develops reinforcement and anchoring materials, including chemical anchoring adhesives, mechanical anchors and carbon fiber reinforcement systems, for rail transit, nuclear power, bridge and municipal infrastructure projects. The company reports that its products have been used in more than 50,000 engineering projects and exported to markets including Russia, Europe, Southeast Asia and the Middle East. Mankate states its mission centers on providing durable, earthquake-resistant and corrosion-resistant anchoring solutions as domestic alternatives to imported systems.

 Selecting an ETA Chemical Anchor Maker for C1/C2 Seismic Use

 

Media Contact Company Name: Nanjing Mankate Science & Technology Co., Ltd. Website: http://www.nj-mkt.com